Menu Close

Benchy D1

Filament: GEETECH WHITE PLA 1,75mm
Untergrund: GFK
Dauer: 1:35
Lagerung Filament: so in Wohnung

Gedruckt mit den Einstellungen:

# generated by Slic3r 1.3.1-dev on 2018-08-30 10:12:52
adaptive_slicing = 0
adaptive_slicing_quality = 75%
avoid_crossing_perimeters = 1
bed_shape = 0x0,300x0,300x300,0x300
bed_temperature = 55
before_layer_gcode =
between_objects_gcode =
bottom_infill_pattern = rectilinear
bottom_solid_layers = 3
bridge_acceleration = 0
bridge_fan_speed = 100
bridge_flow_ratio = 1
bridge_speed = 60
brim_connections_width = 0
brim_width = 0
compatible_printers =
complete_objects = 1
cooling = 1
default_acceleration = 0
disable_fan_first_layers = 3
dont_support_bridges = 1
duplicate_distance = 6
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
end_gcode = G92 E0\nG1 E-15 F9000\nM104 S0 T0 ; turn off temperature\nM140 S0 ; turn off bed\nG1 X320 Y290 F10000 ; lower bed\nM84 ; disable motors
external_perimeter_extrusion_width = 0
external_perimeter_speed = 45%
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 1
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_cost = 20
filament_density = 0
filament_diameter = 1.75
filament_max_volumetric_speed = 0
filament_notes = ""
filament_settings_id =
fill_angle = 45
fill_density = 20%
fill_gaps = 1
fill_pattern = rectilinear
first_layer_acceleration = 0
first_layer_bed_temperature = 80
first_layer_extrusion_width = 200%
first_layer_height = 0.3
first_layer_speed = 18
first_layer_temperature = 225
gap_fill_speed = 20
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
has_heatbed = 1
host_type = octoprint
infill_acceleration = 0
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 80
interface_shells = 0
interior_brim_width = 0
label_printed_objects = 0
layer_gcode =
layer_height = 0.2
match_horizontal_surfaces = 0
max_fan_speed = 100
max_layer_height = 0.3
max_print_speed = 200
max_volumetric_speed = 0
min_fan_speed = 35
min_layer_height = 0.15
min_print_speed = 10
min_shell_thickness = 0
min_skirt_length = 50
min_top_bottom_shell_thickness = 0
notes =
nozzle_diameter = 0.4
octoprint_apikey = XXXX
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].gcode
overhangs = 1
perimeter_acceleration = 0
perimeter_extruder = 1
perimeter_extrusion_width = 0.4
perimeter_speed = 60
perimeters = 3
post_process =
pressure_advance = 0
print_host = XXX
print_settings_id =
printer_notes =
printer_settings_id =
raft_layers = 0
regions_overlap = 0
resolution = 0
retract_before_travel = 2
retract_layer_change = 1
retract_length = 4
retract_length_toolchange = 10
retract_lift = 0
retract_lift_above = 0
retract_lift_below = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 40
seam_position = aligned
sequential_print_priority = 0
serial_port =
serial_speed = 250000
shortcuts = fill_density;infill_only_where_needed;overhangs;thin_walls;spiral_vase;brim_width;support_material
skirt_distance = 12
skirt_height = 1
skirts = 2
slowdown_below_layer_time = 7
small_perimeter_speed = 30%
solid_infill_below_area = 70
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 30%
spiral_vase = 0
standby_temperature_delta = 0
start_filament_gcode = "; Filament gcode\n"
start_gcode = M280 P0 S160; BLTouch alarm reloase\nG4 P100; delay for BLTouch\n; G1 E-5 F4500 ; Zieht Filament 5mm\nG28 ; home all axes\nG29 ; Auto Bed Leveling\n; G1 E5 F4500 ; Schiebt Filament 5mm vor\nG4 S10 ; kurz warten \nG12 ;G12 P1 S1 T12 (Triangel) ; Nozzel Cleaner\n\nG1 X150 Y150 Z50 F10000 ; Startposition
support_material = 0
support_material_angle = 0
support_material_buildplate_only = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_extrusion_width = 0
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_max_layers = 0
support_material_pattern = pillars
support_material_pillar_size = 2.5
support_material_pillar_spacing = 10
support_material_spacing = 2.5
support_material_speed = 60
support_material_threshold = 60%
temperature = 205
thin_walls = 1
threads = 2
toolchange_gcode =
top_infill_extrusion_width = 150%
top_infill_pattern = rectilinear
top_solid_infill_speed = 80%
top_solid_layers = 3
travel_speed = 130
use_firmware_retraction = 0
use_relative_e_distances = 0
use_set_and_wait_bed = 0
use_set_and_wait_extruder = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 1
xy_size_compensation = 0
z_offset = 0
z_steps_per_mm = 0

Schreiben Sie einen Kommentar

Ihre E-Mail-Adresse wird nicht veröffentlicht. Erforderliche Felder sind mit * markiert.

Diese Website verwendet Akismet, um Spam zu reduzieren. Erfahren Sie mehr darüber, wie Ihre Kommentardaten verarbeitet werden .